lm-sensors
Pour fixer le problème des sensors OVH qui affichent des [ALARM]: - carte mère <strong> Intel DH67BL </strong> et le module <strong> w83677HG </strong> / <strong> w83627ehf </strong> , <strong> kimsufi 16G </strong> et dedier sous debian #—-cut here—- # Chip drivers coretemp w83627ehf #—-cut here—- <strong> edit file: /etc/sensors3.conf </strong> chip “nct6775-isa-0290”
# Fans
# label fan1 "Rear fan"
# set fan1_min 251 # From IDU
# label fan2 "CPU fan"
# set fan2_min 251 # From IDU
# label fan3 "Front fan"
# set fan3_min 251 # From IDU
ignore fan1
ignore fan2
ignore fan3
# There is no fan4 on the board
ignore fan4
# Voltages
# Processor Vcc
label in0 "Vcore"
set in0_min 0.6 # From IDU
set in0_max 1.6 # From IDU
# This should be "12 Volts", but computations are strange
label in1 "+12V"
compute in1 11*@, @/11
set in1_min 11.1 # From IDU
set in1_max 12.9 # From IDU
# AVCC(?) - Not shown in BIOS or IDU
label in2 "AVCC"
set in2_min 3.0 # same as +3.3V
set in2_max 3.6 # same as +3.3V
# +3.3 Volts
label in3 "+3.3V"
set in3_min 3.0 # from IDU
set in3_max 3.6 # from IDU
# +5 Volts
label in4 "+5V"
compute in4 5*@, @/5
set in4_min 4.6 # from IDU
set in4_max 5.4 # from IDU
# Memory Vcc ("SDRAM Vcc" in IDU)
label in5 "MemV"
compute in5 1.5*@, @/1.5
set in5_min 0.4 # from IDU
set in5_max 2.0 # from IDU
# PCH Vcc
label in6 "PCHV"
set in6_min 0.6 # from IDU
set in6_max 1.6 # from IDU
# +3.3 Volt Standby
label in7 "3VSB"
set in7_min 3.0 # from IDU
set in7_max 3.6 # from IDU
# VBAT(?) - Not shown in BIOS or IDU
label in8 "Vbat"
# It shows +2.050 V, seems to be not used
ignore cpu0_vid
# Temperatures
# Labeled as "SYSTIN"
# Guess!
label temp1 "VR temp"
set temp1_max 90 # From IDU
set temp1_max_hyst 75 # From IDU
# Labeled as "CPUTIN"
label temp2 "CPU temp"
set temp2_max 93 # From IDU
set temp2_max_hyst 75 # From IDU
# Labeled as "PECI Agent 0"
# Guess!
label temp3 "Memory DIMM temp"
set temp3_max 90 # From IDU
set temp3_max_hyst 75 # From IDU
# Labeled as "PCH_CHIP_TEMP"
label temp4 "PCH temp"
# Labeled as "PECI Agent 1"
# Not used
ignore temp8
Look after: ~/sensors$ sensors coretemp-isa-0000 Adapter: ISA adapter Physical id 0: +37.0°C (high = +79.0°C, crit = +99.0°C) Core 0: +34.0°C (high = +79.0°C, crit = +99.0°C) Core 1: +37.0°C (high = +79.0°C, crit = +99.0°C) Core 2: +34.0°C (high = +79.0°C, crit = +99.0°C) Core 3: +34.0°C (high = +79.0°C, crit = +99.0°C)
nct6775-isa-0290 Adapter: ISA adapter Vcore: +1.00 V (min = +0.60 V, max = +1.60 V) +12V: +12.32 V (min = +11.09 V, max = +12.94 V) AVCC: +3.36 V (min = +2.98 V, max = +3.63 V) +3.3V: +3.36 V (min = +2.98 V, max = +3.63 V) +5V: +5.36 V (min = +4.60 V, max = +5.40 V) MemV: +1.58 V (min = +0.40 V, max = +2.00 V) PCHV: +1.08 V (min = +0.60 V, max = +1.60 V) 3VSB: +3.42 V (min = +2.98 V, max = +3.63 V) Vbat: +3.33 V (min = +2.70 V, max = +3.63 V) VR temp: +34.0°C (high = +90.0°C, hyst = +75.0°C) sensor = CPU diode CPU temp: +32.0°C (high = +93.0°C, hyst = +75.0°C) sensor = CPU diode Memory DIMM temp: +22.0°C (high = +90.0°C, hyst = +75.0°C) sensor = thermistor PCH temp: +37.0°C intrusion0: OK